An epoxy coating requires an exposed concrete surface to bond to, so the sealer must be removed before proceeding. This is true even if the sealer is in good condition because it just will not work under these circumstances.
The next paragraphs will discuss how sealers block adhesion, how to identify a sealer, and when not to use epoxy. We will explain how sealers prevent adhesion, how to test for one, and when not to use epoxy.
Epoxy sticks because it goes inside the pores of the concrete or it adheres to the rough surface produced by the grinding process.
The sealer is different since it seals either these pores or creates a film on top of the concrete surface.
In this scenario, the epoxy coating will adhere to it rather than penetrate the concrete surface. This way, the epoxy coating will not be able to stick to its initial surface.
Once the adhesion breaks down, the epoxy coating will begin peeling off.
The type of sealer changes how much work the slab needs before coating.
One can do a simple test to determine whether the surface is closed or open. This can be done by pouring water on the floor surface.
The floor will look like it is absorbing the water, meaning that it is an open surface, whereas the water will form beads, indicating a closed surface.
It is important to test the surface in multiple areas and not only the traffic lanes. The sealer tends to wear off where people walk on but remains in other areas such as walls, beneath old shelves, and in isolated areas. It may appear to pass when tested in the middle of the room.
Water beading can also happen because of the presence of oil, wax, tire marks, and even curing compounds, which act as a bond breaker.
In commercial epoxy flooring Melbourne it is possible to identify the material by fit out history or past tenants.
Grinding with diamond wheels is the procedure followed. It slices through the sealant and removes the soft upper layer, leaving behind a profile that can be bonded by a new epoxy coat system.
While chemical strippers have the ability to break down film sealants, they usually leave some residues in the pores.
Acid etching is not helpful since the acid cannot penetrate beyond the sealer to reach the concrete. That is how most do-it-yourself kits fail on sealant coated floors.
After grinding, the floor is swept and the water test is repeated on the slab surface. Any areas that still bead must be ground.
The cracks will be fixed after the moisture test before priming, as indicated in this guide on epoxy flooring in Melbourne.
Quite a number of commercial floors in Melbourne will already have a sealer applied to them. This could come in the form of old grind and seal jobs done in warehouses, sealed showroom floors, or retail fit-out floors.
Sealer removal becomes part of the grinding process and will change the scope of work, hence needs to be included in the quote right from the start.
When comparing quotes for commercial epoxy flooring in Melbourne, it is necessary to see whether this has been included separately in the quotation.
Grinding can often be done in phases if the project is a busy one, with the work done outside regular opening hours. It is important to discuss how dust control and access will be handled at the outset.
Epoxy is not always the solution. If the existing seal on the floor is good but just needs rejuvenating, then having the floor resealed might prove a more cost-effective process.
Another issue that may arise with the installation of an epoxy floor is moisture in the concrete slab. Standard epoxy reacts badly to vapours rising from underneath and creating bubbles.
Aesthetic issues must also be considered. An epoxy finish will mask all the original characteristics of the concrete floor.
A venue designed around a concrete look may require something else entirely.
However, an epoxy coating can be applied on a sealed slab, but not until the sealant is stripped.
Urban Concrete Floors will test your floor for sealant and moisture content before advising you on the right system to apply.
Check out our commercial epoxy floors Melbourne, or contact us to schedule an appointment today.
It is impossible. Epoxy will be glued to the sealing layer, not to the concrete itself, and its adhesion will depend on the quality of that previous layer.
No, because epoxy will be coated directly onto the ground concrete with a special primer. Sealing first will interfere with the bonding and cause peeling.
Yes, but only after grinding. Polished concrete is a identified smooth surface, which means epoxy won’t have anything to stick to, unless the surface is opened by grinding.
If you are building your dream home or renovating to transform your space...
Upon completion of our projects, we provide customers with a Care & Maintenance Guide for
Discover our range. Download brochures for unique concrete floor finish insights.